Mustang - Any Fender Mustang I/II/II/IV/V amp can now be controlled by MIDI

Started by admin, September 09, 2017, 07:32:46 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

admin

FWIW - any Fender Mustang amp ( except the Mustang GT) can now be fully MIDI controlled

http://www.primovasound.com/pdf/MIDX_20_Mustang.pdf



thanks to the PrimovaSound MIDX-20
http://www.primovasound.com/midx_20.html

FENDER MUSTANG
If you use Fender Mustang™ Amplifiers you can control every aspect of up to two Mustang amplifiers using regular MIDI commands.





mooncaine

I got real excited--well, first morning coffee excited, so still a bit slow on the uptake.

There is no Mac-compatible software for this device, right?

admin

The MIDX-20 config app is Windows only - host a virtual Windows environment with VMWare Fusion or Parallels, or Apple bootcamp with a Windows 7 partition 

you must use a MIDI Interface with a standard MIDI 5 pin DIN I/O

every audio interfface fro my DAW has 5 pin MIDI /IO ( Focusrite, MOTU) or use a Roland UM-ONE MKII USB to MIDI I/O cable

to connect to MIDX-20

then use any OSX MIDi App to control the Mustan

alf45tar

FYI the PrimovaSound MIDX-20 can be replaced by a Windows software. I just released the porting of mustang-midi-bridge to Windows.
It is based on the same MIDI messages of PrimovaSound MIDX-20 hardware and it is easy to install and use (compared to the original Linux version).
Any Windows MIDI interfaces are supported (including rtpMIDI and ipMidi).

https://github.com/alf45tar/mustang-midi-bridge-win if you want to give a try

Cheers
alf45tar

admin

Quote from: alf45tar on April 06, 2020, 12:20:39 PM
FYI the PrimovaSound MIDX-20 can be replaced by a Windows software. I just released the porting of mustang-midi-bridge to Windows.
It is based on the same MIDI messages of PrimovaSound MIDX-20 hardware and it is easy to install and use (compared to the original Linux version).
Any Windows MIDI interfaces are supported (including rtpMIDI and ipMidi).

https://github.com/alf45tar/mustang-midi-bridge-win if you want to give a try

Cheers
alf45tar

Very Good!

Wish there was a version for  Mustang GT  / GTX on FW 3.0

admin

Report of Mustang Floor owner using MIDX-20 for remote MIDI control of Mustang Floor Internal FX
http://web.archive.org/web/20200317013908/https://forums.fender.com/viewtopic.php?f=27&t=109864

vtgearhead

Quote from: alf45tar on April 06, 2020, 12:20:39 PM
FYI the PrimovaSound MIDX-20 can be replaced by a Windows software. I just released the porting of mustang-midi-bridge to Windows.
It is based on the same MIDI messages of PrimovaSound MIDX-20 hardware and it is easy to install and use (compared to the original Linux version).
Any Windows MIDI interfaces are supported (including rtpMIDI and ipMidi).

https://github.com/alf45tar/mustang-midi-bridge-win if you want to give a try

Cheers
alf45tar

Good work!  Just FYI:  The terms of the GPL license (a) do not permit you to remove the license statement and (b) require that you "make the original code available" - which in this case means a link back to the original projects (as I interpret it).  Thanks for your consideration in correcting these issues!