AMT U-2 Pangaea Ultima Brain Frame

Started by donaldduck, September 01, 2020, 03:23:48 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

donaldduck

https://amtelectronics.com/new/start-of-sales-amt-ultima-u-2/
https://amtelectronics.com/new/amt-pangaea-ultima-u2/

(not just a pedal IR loader, it has preamp, reverb and more).
It is possible to load different firmwares with different functions/effects (see below).

When (if?) they add a tuner it will be all-in-one my swiss army knife pedal.

01 – IR CabSim Fx

The main firmware that comes with the device by default.
A feature is an analog-digital preamp section with three channels: clean, low & high gain.

    Noise Gate (global setting)
    Compressor
    Analog Preamp (Clean / Low gain / High gain)
    Power Amp (9 types)
    IR cabsim (1 IR for both L/R channels per preset)
    Parametric Pre/Post EQ
    Hi/Low pass filters + Presence
    Delay or Reverb effect per preset
    + other features

02 – Modulation FX

The firmware that turns "Ultima" into an effects processor is designed for the case when your Pedalboard, which already has preamp/distortion pedals, requires expanding the sound palette due to various modulation effects.

    Noise Gate (global setting)
    Compressor
    Resonance Filter (wah-wah etc.)
    Flanger
    Chorus
    Delay
    Tremolo
    + other features

03 – IR Stereo CabSim

The firmware that turns the device into a powerful stereo IR impulse responses cabinet emulator.

    IR Stereo cabsim (2 IR's per preset: the first wav IR for the LEFT channel, another one wav IR – for the RIGHT channel)
    Parametric Pre/Post EQ
    Hi/Low pass filters + Presence

04 – Stereo Delay

Multifunctional STEREO IN/OUT Delay effect.

05 – Stereo Reverb

Multifunctional STEREO IN/OUT Reverb with the following types:

    Gold Reverb
    Hall
    Room
    Plate
    Spring
    Gate
    Reverse

06 – Pre/Post FX

The firmware that turns the Ultima U-2 device to the PRE / POST effect processor.

PRE section:

    Noise Gate (global setting)
    Compressor
    Phaser
    Resonance Filter (wah-wah etc.)
    Flanger

POST section:

    IR cabsim (1 IR for both L/R channels per preset)
    Parametric Pre/Post EQ
    Hi/Low pass filters + Presence
    Delay or Reverb effect per preset
    + other features

SPECIFICATIONS

IN L, IN R – Inputs of the Left and Right channels:
– input impedance 470 kОм
– rated input voltage of audio signal 0.316Vrms (-10dBV)
– maximum sinusoidal voltage 2.5V (+8dBV)

AUX IN
– Input impedance 2kOhm
– maximum sinusoidal voltage 0.85V (-1.4dBV)

OUT L, OUT_R – Outputs of the Left and Right channels:
– output impedance 1,5kOhm (unbalanced output)
– maximum sinusoidal voltage 2,6V (unbalanced output)
– phantom power protection – present

PHONES – Output to headphones:
– minimum headphone impedance 32 Ohm
– maximum output sinusoidal voltage (no load) 2,6V (8dBV)
– output impedance 12 Ohm

POWER
– Voltage DC 12V
– Current consumption Approx. 300mA

CHARACTERISTICS OF IR FILES
– Type: WAV, IR A/D – D/A converters 24 bit
– Sampling frequency: 48 kHz
– IR length: 1024 samples (21.3 msec)

– S/N: 115dB.
– Latency: 1.2 ms / 0.0012 s
– Codec: AD\DA AK4621

DIMENSION (HxWxD) 47mm x 55mm x 95mm

WEIGHT 270 g (without package)